All bsi british standards available online in electronic and print formats. Hot rolled low carbon steel sheetplate and strip for cold forming class 2. Continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels. Uni en 10051 continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape 6 tolerances for sheetplate 6. En 10051 engineering tolerance rolling metalworking scribd. En 10219 welded tubes for structural purposes tolerances. At the enquiryorder stage it is necessary to define which of 4 classes ad is required.
Din en 10051 201102 continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape. Tolerances to en 10051 for continuously rolled hot rolled. For the time being please refer to the stainless steel advisory service. In the event of any deviation from the current standard, the latter shall prevail.
The four dimensional tolerance categories are a, b, c and d. Products with a specified minimum yield strength 460 nmmand en 10029 free in pdf format. Delivery requirements for surface condition of hotrolled. Uw swansea athens, university of wales swansea, 18062008 15. Thickness shall be measured at any point situated more than 25mm from the transverse or longitudinal edges of the plate, other than locally ground areas. Download our bs en 10160 ebooks for free and learn more about bs en. Tolerances on plate less than 600 mm wide shall be agreed at time of enquiryorder. The uk participation in its preparation was entrusted to technical committee ise12, structural steels, which has the responsibility to. This standard covers continuously rolled hot rolled flat products with a rolled width of 600 2200mm inclusive in nonalloy, alloy and stainless steels. Steel names en 100272, designation systems for steels part 2. Amendments din en 10147, july 2000 edition, din en 10154, august 2002 edition, and din en 10214 and din en 10215, april 1995 editions, have been superseded by the specifications of en 10326. Continously hotrolled uncoated plate, sheet and strip of nonalloy and alloy steels. Tolerances on thickness for continuously hot rolled low carbon steel sheetplate for cold forming.
En 10051, continuously hotrolled uncoated plate, sheet and strip of nonalloy and alloy steels tolerances on dimensions and shape en 10055, hotrolled steel equal flange tees with radiused root and toes dimensions and tolerances on shape anddimensions. Amendment to en 10051, in which a table for tolerances on thickness for continuously hotrolled low carbon steel sheetplate for cold forming. It is intended to publish an article on this standard. Continuously hotrolled strip and platesheet cut from. Continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on. This british standard is the official english language version of en 100256. The standard governing surface defects and permissible ground areas of hot rolled plates is en 101 3. En 10051 engineering tolerance rolling metalworking.
Hot rolled products en 10051 defines five categories. En 100561, structural steel equal and unequai leg angles part 1. Din v 17006100 is the standard corresponding to cen report cr 10260 referred to in clause 2 of the en. This does not preclude the free use, in the course of implementing. En 10029, hot rolled steel plates 3 mm thick or above tolerances on dimensions, shape and mass. Tolerances to en 10029 for hot rolled plate 3mm and above. Din en 10051 continuously hotrolled strip and platesheet cut from wide strip of nonalloy and alloy steels tolerances on dimensions and shape. Din en 10051 rolling metalworking engineering tolerance.
The uk participation in its preparation was entrusted to technical committee. Hot rolled round steel bars for general purposes dimensions. Tolerances for sheet and plate thickness the tolerances on thickness for continuously hotrolled low carbon steel steelplate for cold forming according to en 10111 are given in table 1. This standard covers continuously rolled hot rolled flat products with a. Tolerances on dimen sions and shape in en 10051, the thickness tolerances are divided according to four different yield strength classes. Tolerances to en 10051 for continuously rolled hot rolled plate sheet and strip. This british standard is the official english language version of en 100253. En 10051, continuously hotrolled uncoated plate, sheet and strip of nonalloy and alloy steels tolerances on dimensions and shape.
1074 1199 204 9 335 1116 1448 624 1064 1576 196 1276 833 66 262 1119 614 212 193 592 1549 1593 1479 1175 1154 298 204 212 1355 306 993 161 70 1337